Post Offer Free
WUXI XITONG TECHNOLOGY GROUP  

Gold Index: 6481

You are here: home  > Daily 2KM Distance Hot In Place Asphalt Recycling Machine Road Maintenance Equipment

Daily 2KM Distance Hot In Place Asphalt Recycling Machine Road Maintenance Equipment 

Place of Origin: Zhejiang, China (Mainland) 
inquire
Add to My Favorites
HiSupplier Escrow
Share |

Product Detail

Model No.: ARHR-5120A

Daily 2KM distance hot in place asphalt recycling machine road pavement maintenance
 
 
<stro

Daily 2KM distance hot in place asphalt recycling machine road pavement maintenance

 

 

Description:

Hot in-place recycling

A kind of preventability maintenance technology, which could repair damages that irrelevant to base course load capacity or pavement structure, such as rutting, crack, decompaction, friction coefficient reduction, asphalt flushing, vertical& horizontal crack, reflection crack, roughness descent, pot hole and stripping, tec.

Advantages:

Comparing to traditional road maintenance method, hot in-place recycling has numerous advantages, which lies in:

. Effectively reduce the cost of highway maintenance

As traditional ways of renovation of asphalt pavement, asphalt mixture would be fully milled off before repaving of new mixture, however, hot in-place recycling technology could make 100% use of original pavement material, only with adding of regenerant and a small quantity of mixture, which saves large sums of materials expenses, transport charge and waste disposal fee, consequently reducing highway maintenance cost and saving engineering cost above 40%.

. Effective use of irreversible natural resources

Both asphalt binder and aggregate belong to irreversible natural resources. During construction of hot in-place recycler, realization of reusability of above two materials ensures the effective utilization of natural resources.

. Being of great value in environmental protection

During maintenance of asphalt pavement, pollution caused by dust would be effectively reduced through application of hot in-place recycling technology. Reusability of original material prevents those non-degradable waste material from being discarded or buried, avoiding pollution against environment.

. Reduce traffic jam

Due to the small demand for new material on site, number of necessary trucks would be greatly reduced, also, influence caused by construction vehicle against traffic would be greatly reduced. During construction of hot in-place recycler, only limited distance of certain lane is required to close according to traffic flow, when other lanes remain normal traffic. In addition, traffic would be reopened after temperature of constructed road surface dropping below 50, which would minimize traffic jam brought by closing construct.

. Fast construction speed

Daily construction capacity could reach more than 2KM(single lane).

. Easily controlled construction quality

Because of completely heat bonding between recycled pavement and original middle course in both vertical and horizon direction, joint quality could be ensured to bring a significant promotion in pavement construction quality. In addition, its high degree of mechanization avoids the influence of human factors against construction quality.

. Effectively make up for the quality deviation of original pavement construction

Parameters like asphalt-aggregate ratio should be adjusted upon adding new materials before hot in-place recycling construction, which could effectively improve common construction problems like poor flatness, unqualified aggregate composition, inaccurate asphalt-aggregate ratio and unqualified water penetration index.

.Effectively handling pavement transverse crack

Transverse crack would be handled through sticking Fiberglass-Polyester paving mat during hot in-place recycling, meanwhile micro-crack of middle surface course would also be improved.

 

Main performance comparison for hot in-place recyclers in current market

 

Process node control Original pavement heating Original pavement milling
Heating mode Heat source temp. Pavement temp. Trough bottom temp. after heating Degree of aging Milling mode Bank condition
Infrared heating 9001100 250300 100 serious

4-5cm

whole layer milling

110,no broken, no gray material
Normal hot air circulation 350550 190200 70 light 4-5cm whole layer milling 90,light broken,there is gray material
Our layered hor air circulation 350550 First layer 160180 100 light

Single layer, 2-3cm

layered milling

110, no broken, no gray material

 

 

bigPhoto
 Mr. Mr. Jia Wang

Tel: 86-510-85361108
Contact to this supplier

Related Search

Find more related products in following catalogs on Hisupplier.com

Company Info

WUXI XITONG TECHNOLOGY GROUP [China (Mainland)]


Business Type:Manufacturer
City: Wuxi
Province/State: Jiangsu
Country/Region: China (Mainland)

You May Like:

Product (126)